Category: "WiFi"

Pages: 1 3 4 5 6

02/13/14

  02:24:00 pm, by The Dreamer   , 2255 words  
Categories: Digital Photography, Travel, Networking, WiFi, Chromebook

Travel Router - ZuniDigital ZTRP150

Link: http://www.zunidigital.com/?page_id=222

Some time before I bought one, I had often wished I had a Travel Router during my travels. And, I know I looked at whether it would be possible to use my Linux laptop as such.

But, then on November 25th, 2011, Black Friday....meaning I was at Chicago TARDIS at the time....I had on the spur of the moment ordered the ZuniConnect ZTRP150 WiFi Travel Router with USB Charging by ZuniDigital from NewEgg.com.

As I recall, it then sat around for months until I finally set it up, in preparation for possible use on my next trip....Gallifrey One in 2012.

The turn hotel ethernet into WiFi for all my gadgets was really nice, since most hotels only allow one device per room to register for its free or pay wireless. (though I heard some allow pay per device....) But, my reasoning at the time was the large number of Eye-Fi cards that I have in my collection, which are unable to connect to such WiFi, even when its free and its just an EULA page that needs to be accepted.

Otherwise, I wasn't too WiFi dependent gadget heavy then....I could use 3G on my smartphone, and my Kindles all did 3G or something (either exclusively or later with WiFi...I had started carrying the Kindle Fire, original, on trips....so it was the first that would benefit from a travel router.)

It was November 23, 2012 that I started my journey into the world of Chromebook (I had preordered it, and that's when it shipped....at first I was traveling with both my Linux laptop and the Chromebook, but for some time now...I've been going with just the Chromebook. Which has been challenging, like now I can't add SSIDs to my eye-fi cards on the road. So, I have to hope that I got the right ones pre-added to the cards. Along with some of the ones I know what will work, like the SSID for my MiFi2200 or later tethering off of my HTC One (I got the 5GB tethering plan, because lower tiers weren't eligible for employee discount and I had been looking to upgrade from MiFi....but hadn't found a reasonable pay as I go, but can't be activated because I don't live in an area that's covered by it.

Though I did consider exiting the Smartphone crowd and getting a contract Mobile Hotspot, but there isn't anything in an Android 4.3/4.4+ equivalent to iPod Touch....or WiFi only smart phone ???

Now, I guess I've been lucky with the ZuniConnect, which has two modes, Router or WISP. It has both a WAN and LAN port, so there's lots of different ways it could be used.

Long before this, I already had a RoadWarrior travel Ethernet cable in my carry on....so I wasn't stuck if the room only had a jack. And, the router mode was all I needed. It was pretty much plug it in and go everywhere that I stayed.

That was until my previous trip....the one to visit my brother and parents for Christmas. The hotel I stayed at didn't have Ethernet in the room. I had never looked at WISP, but knew it was something I was going to need to use eventually.

Well, it was a bust, because WISP is largely a different configuration in the router, because I would see ZuniConnect or something as an SSID sometimes, but not be able to connect to it. Not sure I know how to connect Chromebook to WPS, or if its possible. etc. But, in the end found that the only way to configure WISP is through ethernet. And, none of my devices had ethernet ports. (I'd still be screwed if I had a MacBook Air along....)

So, I made a note to investigate alternative Travel Routers and to acquire a USB Ethernet adapter for my Chromebook, etc. I eventually got both as part of a larger order from Amazon.com on Jan 22, 2014. I got a "Plugable" USB Ethernet adapter, because it was specifically listed as an adapter from Chromebook. And, I got a TP-Link TL-WR702N, Which sounded like it also did all I wanted, had been favorably reviewed and I've been pretty happy with the TP-Link TL-WR1043ND router that handles my Cox connection to the world....doesn't do all the stuff I liked doing with DD-WRT (though I could DD-WRT it)...but its been rock solid, and since I've moved to running nginx reverse proxy on a DMZ host, the 16 port forwarding limitation isn't an issue. QoS might start to become a concern though. But, I still primarily do that through DD-WRT on AT&T connection to the world. Some day I think I want to try pfSense....

But, that hotel stay wasn't a problem since they're WiFi access was controlled by a password that is given out at check-in....so I could connect all my devices to the WiFi without problems.

Anyways....these items sat around in their packages, until the night before I was to depart for Gallifrey One 2014.

The USB Ethernet adapter just worked and wasn't a problem (though I haven't registered its MAC with my network, which only does reserved DHCP ... its on my list to create a guest network, which can be helpful for discovering MAC address of devices that don't have them printed anywhere on them. But, it hasn't been an issue with wireless devices, since those failed attempts show up in my radius log. Which probably also shows up in the dhcp log (I suppose I should set those logs to forward to zen, so I can see them and add them to the appropriate files in CFEngine 3 repository....still haven't gotten cf-runagent working though.)

The TP-Link TL-WR702N was another story. Again it looks like it needs to be configured manual for WIFi Bridging through its ethernet port, but the ethernet port being dual mode LAN or WAN, its out of scope for its built-in DHCP (which is also disabled by default...) Also of annoyance was that its SSID was fixed, couldn't tailor it to my convention, but rather its own convention ending with the last 3 octets of its MAC. Where the default password is the last 4 octets. It does allow you to change the password, along with other encryption settings, or go open. It has a dropdown list for channel, which had defaulted to AUTO. But, it won't allow you leave the page until its been changed to be the same channel as the selected WiFi. Seems its a flaw with all WISP, that they attach to BSSID.... I have two APs at home, both with the same SSID, but different BSSID (of course) and different channels. Yet, my bedroom is still in a hole.... :))

Could be interesting in a hotel environment where there's going to to be many different BSSID/Channels, which might change throughout the stay.

But, I ran into a problem. I couldn't not get my Chromebook to connect to the Ethernet port. It didn't do DHCP, but Chromebook has options to set things manually, but Chromebook still wouldn't connect. I suspect there's something Chromebook expects to get answers for to determine that the connection makes sense, and the TP-Link doesn't do it. At first I thought the Chromebook was expecting a fully usable Internet connection....which doesn't make sense, since its able to use captive portals, though often the captive portals only block http/https initially, or provide/leak enough to satisfy my Chromebook.... That was until this Gallifrey One trip....

Full story »

05/24/13

  08:20:00 pm, by The Dreamer   , 509 words  
Categories: Home Theatre, WiFi, Storage, Samsung UN50ES6500F, FreeBSD, VirtualBox

I got another HSTi Wireless Media Stick

Link: http://hsti.com/products/wirelessmediastick

I had acquired my first HSTI Wireless Media Stick back on April 24th, 2011 (from a marketplace seller on Amazon.com)...it took some time to arrive and I blogged about it on April 30th, 2011 -- Getting local content to show on my Roku XDS.

Now my Roku has moved to my other HD display (24" 1080p), but that was before my old Samsung HDTV (43" 720p) regenerated into a Samsung Smart 3DTV (50" 1080p).... so I'm back to living room TV being my main viewing device for all content, though TiVo has a box that I could connect to the smaller display to access my TiVo content there....which I may want to get at a later date. The majority of content I watch is from TiVo...one of these days I need to setup my blu-ray player so I can get back into watching DVDs (not sure when I'll have blu-ray discs, but need to get back on my netflix backlog).

But, the other day I had an mp4 file that I needed to play....and I thought I should get someway to do that to my 50" HD display... Had to settle with using the Roku for a bit. And, decided that the plan will be to acquire another HSTi Wireless Media Stick.

After searching around online, eventually found that ordering directly from HSTi was the only option now. So, I ordered another one on May 17th. It arrived yesterday. But, I didn't set it up until I got home from work today. Somehow I had forgotten again that HSTi is in Calgary, Alberta. Not that I'll be going up there in the immediate future....

Anyways, no big surprises...good thing I had solved my USB2.0 and Windows 7 in VirtualBox on FreeBSD problem (got a Silex SX-DS-4000U2). I'm sharing TARDIS from orac to it still, since I don't yet have a replica on zen yet (need to free up space). Though when I moved the HSTi Wireless Media Stick it had forgotten the share, so had to pull up web again and add it back. Interesting that its graphic shows the itself, while the graphic on my older stick is that of the original Wireless Media Stick (it used to be the correct graphic, but after an update it keeps showing the graphic of the older version.) Though this one came from the factory with the latest firmware, so who knows what'll happen when there's an update.

Was interesting using the SmartTV to view it, though wonder if it'll be a problem with it constantly discovering the stick every time I turn it on and presenting dialogs and such. Afterwards I tried the Amazon app to see if that was working yet....it was still saying I needed to update my TV, though this time there was an update....and now that works. Which might make it interesting to decide on what I should do. The only problem with using the SmartTV versus some other viewer....the TV is only 2.1 audio while other routes I can get 5.1, and its a different input on my receiver....

Oh well, back to other projects....

12/01/11

  04:27:00 pm, by The Dreamer   , 1531 words  
Categories: General, Digital Photography, Hardware, Computer, Travel, Networking, WiFi, BOINC, Safety & Security, b2evolution, Quicken/TurboTax

Cyberweek Activities

This being Cyberweek...I tried to cram some stuff in other than just recovery from Chicago Tardis into this week.

Though I haven't actually gotten to all the things yet...I felt that I should start this post before I forget all the things I wanted to cover. Too late :no:

Anyways...one of the important items was new CO detector. I used to have a First Alert CO400?, battery operated CO detector that took a couple AA batteries and didn't do much else. I was looking to buy something like it again, except reading the negative reviews on amazon.com... a number of other people were complaining that unit disintegrates when you try to change the batteries. Which is why I was needing to replace my old one. So, I decided that maybe I would look at a different brand this time around.

Also noted that these things have like a 5 year life expectancy...though my First Alert CO detector was only a year old. I noticed that Kidde CO detectors claim a 7 year life span (though only a 5 year warranty). Though (in part due to Amazon 'recommendations') I got the Kidde KN-COPP-B-LPM, which has a digital display....showing current CO levels and historical levels, etc. Which I debated on whether I would want to know if there was a CO level, that wasn't alarming.

Don't know if I paid attention to the fact that it uses 3 AA batteries....one odd thing I've noticed, is that it doesn't say if I should replace batteries regularly....but I suspect it'll be part of the same routine with replacing smoke detector batteries.

Though I don't think I'll replace the CO batteries along with the smoke detector ones on December 25th (because of long DST, I had changed my bi-annual to be on or around June 25th and December 25th.) Though, I've already replaced the battery early in one of the smoke detectors. Odd, because there hadn't been any nuisance trips in some time...and it isn't one that is typically set off by these situations. (usually ones that nuisance trip is the detector in the living room [near the kitchen or the first bedroom from the kitchen. Yeah...something I'm burning on the stove or in the microwave is usually the cause.)

But, getting a new set of 4 9V batteries was something I got in my recent cyberweek purchasing...

Pages: 1· 2· 3

11/20/11

  12:49:06 pm, by The Dreamer   , 1764 words  
Categories: Stuff, WiFi, Furnishings, Amazon Kindle, Barnes & Noble Nook, Nintendo 3DS

Kindle Fire -- the first 72 hours

Well, it's been just a touch over 72 hours since I got my Amazon Kindle Fire.

I pre-ordered it shortly after it was announced, with an ETA for November 17th with free 2-day Amazon Prime shipping. I knew there was a chance that they should ship early, because they did that the last time I pre-ordered something (The Kindle 2 and the Nintendo 3DS). But, its been a busy week...and I tried my best to keep my calendar open to receive it....I had an appointment pre-Kindle Fire announcement on the 14th, and I was keeping the 15th open for something that was later scheduled in conflict to the 14th....and ended up having an appointment on the 16th. If I had some notice from Amazon just before they shipped to adjust its timing...I might've...since the 15th being open now...I could've gotten it then. Instead I had to wait for UPS to make a redelivery attempt and bring it to me on the originally scheduled day... November 17th.

I didn't open it immediately when UPS gave it to me, in fact I put it down first and then had to find it before I could open it. It was easy to open...no info with it, but I eventually found the power button and it eventually booted and walked me through setup...though complicated by the fact that I needed to know its MAC address to add it to my radius and dhcp server configs. Plus I hadn't decided on an IP for it yet. Fortunately with radius access controls, its easier to find the MAC address of new devices than before.

It came pre-activated, in fact I had seen it in my kindle account before they shipped it (but no serial number was associated with the registration yet)...but I changed its name to follow the naming scheme I had gone with (if you can call only one previous device the basis of a scheme)...though I am tempted to get a Kindle Touch 3G to succeed my Kindle 2....though wonder if they're going to come out with a DX version? What I liked was that my Kindle Fire's email address was my first Kindle's address with '42' added to the username. &#59;D Though there's a bunch of Kindle apps associated with my account that I don't recognize....wish the automatic naming was more descriptive. Suspect some are devices where I had to reinstall the system or have since be retired.

Though I wasn't crazy enough to buy content for it before receiving it...though I was tempted.

Anyways...what I was getting to, was once I got it working on my WiFi network, the next step would've been registration...and it flashed it briefly before telling me that it was registered and had the name I have given it earlier. And, then it was to update itself. So I found somewhere to plug it in and left it.

Big problem that is getting worse in my home now...so many things that need to get plugged in, and all the convenient outlets are already full and now I'm running out of inconvenient ones too. The Kindle Fire is using one of those inconvenient ones. I've been meaning to build myself some kind of charging center, similar to the kind of thing Cali Lewis was presented doing in a GeekBrief. Perhaps I'll have to step up plans to get around to 'building' it. Just haven't found that piece of furniture to buy to modify yet... Probably just a matter of time that I come across something reasonable on Amazon.com with Prime and get it though....

Full story »

11/10/11

  04:11:52 pm, by The Dreamer   , 881 words  
Categories: General, Wireless/iPhone, VoIP, WiFi, Safety & Security, Cox HSI, AT&T DSL, Broadband, Amazon Kindle

Cox Cable was a no show today....

This afternoon's tale starts on Tuesday, November 8th.

At about 9:30am, I get an email from Cox about Wednesday's EAS test for 2pm EST....shouldn't be a problem, won't be home and nothing should be recording then...

Then at about 11:30am, I start getting pages that my Cox connection (among other things) has gone away. Well, the other things were because without Cox...there's no DNS or NTP...so things that tested or depend on that also failed. Though monitoring from work just showed Cox down.... At least I still have DSL....tweak some stuff back to being DSL centric, and bounce my cable modem a few times.... I had switched away from being DSL centric after a recent significant DSL outage.

Eventually cable service comes back, and I think all is good. Though I don't notice that not everything in nagios has cleared. And, when I come home...I find that I still have no Cox internet service.

I turn on the TV to see if I'm at least getting a signal....but I only checked the channel that was default...didn't check further. I then get on with Cox to find out why my service is down.

Strange that I often have trouble right around bill due time. But, I use EasyPay, so they automatically get paid. And, this month the auto-pay date is November 9th. New bill came out around October 27th (in fact later when I got confirmation that they had processed the payment, that's what it said). Always interesting that they allow so little time between sending the bill to when it needs to get paid. Its probably to keep us from dropping services between getting the bill and paying it. Like dropping Movie Pak....a while back they moved BBC America to the Movie Pak, so I had to add that to my service quickly....but sometime later they moved it back to the Variety Pak...so I should probably drop the Movie Pak...but I never seem to get around to it. I don't watch anything else in the Movie Pak (but at least I do from the Variety Pak.)

But, I check and account is current. I also got alert from bank of the pending charge too.

So, I get on with Cox support to find out what's up or not....and after they get my account information, come back saying a technician call is needed and say the earliest is Thursday between 1-3pm. Ok...then I'm asked if there's anything else, and I'm disconnected.

Seems like that's one way to avoid the National EAS test....

I had turned the cable modem on and off a few times, with longer off times, and checked connections and such...to no luck, but couldn't recall if I left it on or off overnight. When I get up...there's still no Cox Internet service. I restart the cable modem, and presto...I have service.

Pages: 1· 2

07/24/11

  11:49:00 am, by The Dreamer   , 2214 words  
Categories: Digital Photography, Hardware, Software, Computer, DVDs / NetFlix, WiFi, Storage

Morning Orac outage

Well, Orac was being somewhat unresponsive this morning.... Looks like early this morning the system stopped answering to Cacti, with the temperature of the GPU rising to a new high. Don't know what the high would've been, because there was no snmp data for a while. GPU temp did recover, but the display did not.

Ended up rebooting, needed the excuse to see external journal work....

Once backup, I switched back to internal journal...but one of maximum size rather than default size. And, then shutdown the system to extract the PCI Compact Flash card. During the reboot to see external journal work...I realized that I wasn't likely to see much performance gain from getting faster compact flash since the card itself was only UDMA/66. So the 133x CF is already faster than the card?

Probably should've fsck'd manually after the switch back....some discussion thread suggested doing this after fiddling with journal settings. But, its fsck'ng now after the boot back up. Apparently superblock had invalid external journal superblock hint? And, auto fsck failed, requiring manual fsck.

Downside of internal journal is that it can only be a max of 400MB (an improvement from the 128MB default I had before)...but that's only like 0.01% of my total space. And, there was a discussion thread that seemed to suggest a journal size of 0.2% would yield better improvement....I didn't do the whole 16GB CF card...though wonder how much that would've helped.... But 0.2% would call for a journal of ~10.9GB. Suppose I could turn off data journaling, especially since there are files that backuppc puts down that are bigger than the 400MB journal. Though I think the ordered/writeback modes usually just do metadata journaling, while I had switched it to data journaling when I was playing with external journals...but I didn't switch it back.

Wonder which of writeback or ordered would be more optimal for this FS? :??:

Full story »

Pages: 1· 2· 3

07/17/11

  03:13:02 pm, by The Dreamer   , 817 words  
Categories: Software, Networking, WiFi

The Airport Express Tangent

Being that it is really hot today, I didn't feel like going out and figured I could tackle some of the many projects that I've been putting off.

Before I started, I happened to look at cacti...not sure why I had at first, but I went off and looked at the Airport graphs. Nothing has associated yet with my Airport Express, is there something wrong...with it or the clients?

Wondered if it was the use of manual versus automatic channel selection....perhaps it doesn't see the Airport Express as a strong choice, though sitting right next to it...it should've dominated.

But, I tried automatic to see what channels it would jump to. I was kind of surprised that the Airport Extreme jumped from 1 to 10. First in that I thought 1 was the best, and second I expected it to pick one of 1, 6, 11. Though when I was running the Belkin APs, I was running them on 2 and 10.....there is one other AP somewhere in the condo that is using channel 10. And, oddly...same SSID as I was using, except all lower-case (instead of capitalized). But, I've since turned off the Belkin APs...so I don't care anymore?

I then configured the Airport Express to automatic...and it jumped from channel 11 to 1. Okay then....let's see how that works.

Full story »

07/09/11

  07:12:06 pm, by The Dreamer   , 913 words  
Categories: Hardware, Computer, Networking, WiFi

Airport Express service for Lunatic Haven

That's right, I got an Airport Express to go with the two Airport Extremes that I have in my home.

As I mentioned before, I had gotten the second Airport Extreme to extend my 'wired' network to a room where the CAT5 to that room was bad and not wanting to try to fix it. The problem is that I run separate SSIDs on my main Airport Extreme for a/n and b/g/n frequencies. Since things that can use 5Ghz, tend to work better around here. And, there didn't seem to be a reliable way to ensure that 5Ghz was always chosen unless it had a different SSID. Something I learned about doing from LISA &#59;D

Well, the second extreme was set to extend my network, and I told it to go for the 5GHz SSID. But, in extend wireless mode...there's no option to set different SSID(s)....so it was advertising my 5GHz SSID for both frequencies. Wanting to keep things straight, I ended up turning off allow wireless clients to use the second Airport Extreme.

But, increasing number of wireless devices in my home....I wanted to have a better WiFi signal in the bedroom.

Now I did have some older 802.11g access points, and they were on and using a different SSID. Hadn't noticed that I had set the Airport Extreme to do only WPA2 personal until today. The old 802.11g access points originally only did WEP....there was an upgrade to get WPA personal, but it broke the WDS feature that I was using then. But, when I stopped using WDS...I did upgrade but left them on their own SSID because it didn't seem to work too well otherwise.

Though wonder if WPA vs WPA2 would explain it...the other was at the time the Airport Extreme wasn't doing access control and the old Belkin APs had a list of MAC addresses would allow...though it wasn't getting updated that well...

So, I was liking the use of RADIUS to control access on my home network...and wanting to use the same RADIUS to control whatever method I extended my network. So, that pretty much meant....another Airport Extreme or an Airport Express.

I knew there were differences, but I tried to decide if the differences were that important. Apparently, I didn't get it right...but an Airport Express being cheaper than another Airport Extreme...meant that I could try this sooner than later. Plus I there's always the possibility of it becoming part of my arsenal for travel use (except for its dependence on Airport Utility...which is current difficult because I run an Ubuntu laptop....though I am considering a Mac laptop [now instead of a Windows laptop]).

The first difference is that it only has a 10/100 port on it....which was important for extending my network (to TARDIS), but didn't seem important for extending the reach of my wireless now. The other difference (I missed) is that its 2.4GHz or 5GHz....rather than both at the same time.

Was trying to decide if I would have it extend my wireless network by wireless (or wired)...if it were simultaneous dual band....wired would likely be the only choice. Though decided that wired would remain the way to extend my 2.4Ghz network...since the lack of reach of 2.4GHz was kind of why I was doing this.

Full story »

05/30/11

  12:03:00 am, by The Dreamer   , 1362 words  
Categories: Software, Computer, Networking, WiFi, Ubuntu

Freeradius & DHCP Failover

Link: http://deployingradius.com/

So, ever since I looked at adding Mac Address Access Controls to my Airport Extreme...on top of WPA2 Personal, and the fact that my DHCP server only does reserved IPs, security. I used to do Mac Address Access Controls on my previous routers, but it was an easier interface to work with on those. And, I didn't realize how the Time Access worked on the Airport Extreme, the default allow all the time rule at the top tripped me up. So, I thought if I wanted it, I would need a RADIUS server...and I didn't know if I wanted to do that....yet.

But, after I woke one morning and couldn't seem to account for why there seemed to be so much data streaming through my Cox connection...there had been strange spikes in the past, but always figured it was something updating itself while I wasn't home (like iTunes and my podcast subscriptions). But, this one morning...there was no corresponding activity from any of my computers, and I didn't see anything obvious with my TiVos/ReplayTVs. Though I could've just missed it.

So, I fixed the Timed Access control and put my current devices in. With a note that I should really look into installing RADIUS somewhere, so that it would be easier to maintain the list than the airport utility. I would lose being able to find the MAC address of some new wireless device that doesn't have the MAC address stamped on it....for addition to my DHCP server.

Later during the setup in: Another Airport comes to Lunatic Haven I had wiped out the settings....and didn't feel like putting it back in again. Which made it more urgent (in my mind) to get RADIUS working.

So, I went online and searched and searched and searched...on how to do this. I had looked before, and wasn't all that successful. There's no simple how-to apparently. But, I found bits and pieces around, and decided to just go for it.

First, I installed freeradius on my Ubuntu server 'box'.

sudo apt-get install freeradius

It starts right away, now to make it work. And, debug it. Well, most of the examples were for older freeRADIUS versions, so things weren't where it said, or command line switches were different, or it didn't work. I did find some examples of MAC address authorization, but they involved 'Auth-Type := Local' in the /etc/freeradius/users file. But, the clients.conf part seemed right. I strongly considered just doing 'Auth-Type := Accept'...but I wanted to figure this mess out.

client 192.168.1.1 {
        secret = testing123
        shortname = airport
        nastype = other
}

So kept searching and searching....eventually, I found fragments on site called "Deploying RADIUS: Practices and Principles". It confirmed that I was basically on the right track, I just needed to figure out what to put in the users file to make it go from Auth-Reject to Auth-Accept.

Well, the example for MAC Address entry for users I had found was:

001122-334455  Auth-Type := Local,  User-Password == "testing123"

At first I was pointing my Airport Extreme at it and watching the debug output, and watching everything stop working now and then. But, eventually I used 'radtest' to test my freeRADIUS configuration. And, eventually, I found that what I needed was:

001122-334455  Cleartext-Password := "testing123"

And, all was good. I pointed my main Airport Extreme to it, and it everything adjusted and worked. I then pointed the new Airport Extreme at it and things continued to work.

Yay! :cool:

Pages: 1· 2

05/29/11

  10:48:00 pm, by The Dreamer   , 930 words  
Categories: Hardware, Computer, Networking, WiFi, Printers

Another Airport comes to Lunatic Haven

That's another Airport Extreme....

The corner where I put TARDIS and my HP Photosmart 8450xi printer have been having switch problems, or at least I that's what I thought. But, I have replaced the only cable to replace, and both switches. But, still the link will drop out of gigabit after a while. And, then it wouldn't go into gigabit at all anymore.

And, then PRTG reports that things over there disappear every night. What's strange is that its always around the same time.

I thought about buying some network testing equipment, and figuring out what it would take to run a new line in place of the existing one (should be easier than what it would take to run one to a new location). Or doing the ugly and stringing wire along the ceiling....

But, things started adding up....and I wondered just how much I needed the speed. Sure gigabit would help TARDIS backup faster, but that's about all over 100Mbps would get me. The printer is only 100Mbps, so no advantage there. And, likely would be the case for any network printer I were to put there. And, likely not much else is going in the corner any time soon that would need gigabit. So, I wondered about revisiting the WDS option using 802.11n now. I had survived for some time with 802.11g WDS both here and in the past.

Looking at WDS options with my Airport Extreme, it pretty much came down to two options....an Airport Express or an Airport Extreme. Express only has a 10/100BaseT port on it and its a big plug type thing, so if I wanted better than 100Mbps, it would have to be an Airport Extreme. I did look at other routers, but hard to tell if it would work or not, and I'd probably want something using OpenWRT or something and things started getting complicated again.

I do someday think I'll get an Airport Express...though it would require that I have Linux solution to manage it, some way to set it up in a turnkey solution....as a travel router.

But, while I was looking at other WiFi router options...I was looking on eBay, so I wondered about an Airport Extreme that way (instead of using my Educational discount on another).

And, I found some pretty reasonable prices for refurbished units, so I went for one.

Pages: 1· 2

1 3 4 5 6

Now instead of subjecting some poor random forum to a long rambling thought, I will try to consolidate those things into this blog where they can be more easily ignored profess to be collected thoughts from my mind.

Latest Poopli Updaters -- http://lkc.me/poop

bloglovin

There are 20 years 9 months 21 days 43 minutes and 24 seconds until the end of time.
And, it has been 4 years 3 months 7 days 13 hours 19 minutes and 32 seconds since The Doctor saved us all from the end of the World!

Search

March 2017
Mon Tue Wed Thu Fri Sat Sun
 << <   > >>
    1 2 3 4 5
6 7 8 9 10 11 12
13 14 15 16 17 18 19
20 21 22 23 24 25 26
27 28 29 30 31    
Google

Linkblog

  XML Feeds

Who's Online?

  • Guest Users: 2
This seal is issued to lawrencechen.net by StopTheHacker Inc.
free blog tool

hosted by
Green Web Hosting! This site hosted by DreamHost.

monitored by
Monitored by eXternalTest
SiteUptime Web Site Monitoring Service
website uptime